Valor-auto-companion-inc 739DVN User Manual

Direct Vent Gas InsertModel 739DVN (Natural Gas) Model 739DVP (Propane Fuel)Installation and Owner’s ManualDO NOT store or use gasoline or any other

10Clearances6.2 Combustible Mantel ClearanceFigure below shows minimum clearances to combustible mantles.Note: Measure taken from underside of mantel

117.1 Vent LocationThe vent terminal must be located through the roof.This direct vent appliance is designed to operate when an undisturbed airfl ow hi

12Venting991 DV GSCap (High Wind)980 DV GSCap (Low Profi le)923GK DV GS Chimney Liner Kit930 DV GSExtended Cap923F DV GSApplianceFlex Connector2150 DV

13Pack ContentsTake care when removing the contents from the packaging to prevent damage. Check that all the contents are in the packs and are undamag

14Pack ContentsRear Log Rest Remote ControlCeramic Log Set742CFB Cast Iron Front741SFB Standard Metal FrontCeramic Brick Pack739DVN or 739DVP EngineEn

159.1 Window RemovalRemove the bottom center spring-loaded bolt.Turn the 5 remaining spring-loaded bolts 90 degrees to release the window from the fi r

16Remote Control PreparationCAUTION! Do not connect the batteries to the remote control receiver until the wires are connected to the burner control u

17Gas SupplyOnly persons licensed to work with gas piping may make the necessary gas connection to this appliance. You are now ready to hook up the ga

18Panel Installation12.1 Ceramic Panels Installation Remove the Firebox Baffl e by fi rst removing 2 screws on the front fl ange and lifting the Baffl e t

19Log Installation13.1 Ceramic Logs InstallationInstall the Rear Log Rest supplied using 3 screws provided. See fi gure 13.1.Place the Ash Bed in posit

2Table of ContentsIntroduction ... 3Appliance Dimensions .

20Log InstallationRear Log RestSee no. 2 on p. 18Rear Log PinsLeft Center Log PinsFront SupportAsh BedRear LogFront LogLeft Center TwigRight Center Tw

2114.1 Window Refi tting & Checking Fit the window to the fi rebox. Insert the bottom middle spring-loaded bolt and tighten it.Locate the bottom 2 s

2216.1 Side Trim AssemblySlide the corner connection plates into the channels in the top section and one of the side sections. Butt the two sections t

23Final Checks17.1 Final CheckINSTALLER: Before leaving the appliance with the customer, you must check the operation of the appliance.Check correct r

24Operational WarningsPre-Start Up ChecksFOR YOUR SAFETY, READ BEFORE LIGHTINGWARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPL

25 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property dam

26MaintenanceWarning : Use only genuine Valor parts, do not use substitute materials. 20.1 CleaningIt will be necessary to clean the glass periodicall

27Maintenance20.4 ChecksA periodic check of the pilot and burner fl ames should be made. Check after the fi re has been on for at least 30 minutes. The

28Programmable Remote ControlYour fi replace remote control helps you get the comfort, convenience and aesthetics you want from your gas fi replace. The

29Programmable Remote ControlSetting the fl ameUse this setting when you want a particular fl ame level. For instance, you want to watch fl ames burn at

3Thank you for purchasing the Valor 739 Direct Vent insert. This high quality unit is specifi cally designed to be used where installations are restric

30Venting OptionsAPPROVED ALTERNATIVE DIRECT VENT SUPPLIERS FOR VALOR MODELS 739 AND MILES FIREPLACES’ MODELS RF24VENTING PARTS DESCRIPTION VENTING PA

31Warranty1. Extended Warranty CoverageFor a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will

4See section on installation for details regarding clearances and mantel height allowances.Appliance Dimensions** See Page 9 for clearance information

5Safe installation and operation always require common sense. We are also required by Canadian and ANSI safety standards to point out the following: I

6Safety InformationNOTE: Always allow adequate clearance around air openings into the combustion chamber and maintain accessibility clearances for ser

7Specifi cationsNote: Always check appliance label for correct informationMODEL 739 Natural Gas (NG) Propane (LPG)Manifold pressure 3.95 in. w.c. (0.98

8PlanningNOTE: THIS APPLIANCE MAY ONLY BE INSTALLED IN A SOLID-FUEL BURNING FIREPLACE WITH A WORKING FLUE AND CONSTRUCTED OF NON-COMBUSTIBLE MATERIAL.

9ClearancesXY6.1 Existing Fireplace (Masonry or Factory-Built)The model 739 is intended for installation into masonry or listed factory-built fi replac